Pagina 1 van 1

kapittelslot

Geplaatst: dinsdag 03-07-2018, 13:35
door cesman
Ik wil zelf een kapittelslot ontwerpen/maken. Is er een bepaalde maatvoering voor het stokje ten opzichte van de binnenmaat van de ring? bijvoorbeeld twee keer de diameter of is dit te kort door de bocht? :think:

Re: kapittelslot

Geplaatst: dinsdag 03-07-2018, 14:44
door @tjuh
te kort door de bocht, je hebt nl ook te maken met de grootte van een eventueel oogje welke vaak aan het stokje vastzit. en de lengte van je armband/ketting of er ruim genoeg ruimte is om 'm erdoorheen te rijgen (langer stokje) of krap aan (dan kan het stokjes iets korter)
dikte materiaal speelt ook een rol..etc etc.

Re: kapittelslot

Geplaatst: dinsdag 03-07-2018, 14:49
door cesman
:thx: Gewoon experimenteren of is er een formule?

Re: kapittelslot

Geplaatst: woensdag 04-07-2018, 15:53
door @tjuh
wellicht zal er een formule zijn voor degene die ze dagelijks maakt....ik experimenteer....en ben dus op oa bovenstaande gestuit.

Re: kapittelslot

Geplaatst: woensdag 04-07-2018, 16:29
door cesman
Dank je voor de reactie

Re: kapittelslot

Geplaatst: donderdag 05-07-2018, 8:26
door ErwinG
Ik zit toevallig met dezelfde vraag. Vond dit op Ganoksin

Crossbar Catch
In this simple catch (figure 12.23), a cross bar on one end of a chain is free to pivot so it can be laid flat along the chain. This allows it to pass through a ring on the opposite end of the chain. When allowed to hang, the bar is pulled perpendicular and cannot pass back through the ring, thus securing the clasp.

The design is not complicated – the bar is nothing more than a short length of wire with a jump ring soldered onto the middle to provide the connection to the chain. The opposing jump ring should be just large enough that the bar with its jump ring barely fits through.
12-23.gif
12-23.gif (3.92 KiB) 10032 keer bekeken
It is nearly impossible for the bar to slip out of its ring accidentally, but to be absolutely safe, solder another jump ring onto the opposing one (to create a “figure 8” ). When the bar is passed through both, the effectiveness of the catch is doubled – even if it slides through one ring, the odds of it passing through both are extremely low. The bar looks more finished if the ends of the small rod are balled up into small spheres as shown.

The crossbar catch can only work if the section of chain to which the bar is attached can also fit through the opposing jump ring. In the case of a thick chain, it might be necessary to use a smaller loop in the section immediately adjacent to the catch, as seen in figure 12.23.[/i]

Re: kapittelslot

Geplaatst: donderdag 05-07-2018, 8:40
door cesman
:thx:

Re: kapittelslot

Geplaatst: donderdag 13-09-2018, 18:31
door cesman
E376F74B-A97C-44F7-9662-7E7FB4EB814A.jpeg
Gelukt, wil even het resultaat delen b:D

Re: kapittelslot

Geplaatst: donderdag 13-09-2018, 19:32
door ErwinG
cesman schreef:E376F74B-A97C-44F7-9662-7E7FB4EB814A.jpegGelukt, wil even het resultaat delen b:D
Nice! En delen is aardig :-)

Mooie foto ook, durf die van mij bijna niet meer te laten zien :tandpasta:
IMG_20180823_202925.jpg
IMG_20180823_202925.jpg (163 KiB) 9586 keer bekeken

Re: kapittelslot

Geplaatst: donderdag 13-09-2018, 22:14
door cesman
Ook mooi hoor **) mooie afwerking, top

Re: kapittelslot

Geplaatst: vrijdag 14-09-2018, 4:09
door @tjuh
dat is een mooi slot geworden! en goede oplossing ook om (met dubbele en gebogen oogjes) het stokje mooi plat op je slot te krijgen liggen.

ik heb zelf de indruk dat een platgewalst stuk draad mooier bij het ontwerp had gepast (en dan de uiteindes mooi afgerond gevijld).

Re: kapittelslot

Geplaatst: vrijdag 28-09-2018, 8:32
door ErwinG
Vond nog een mooi uitgevoerd kapittelslot (gemaakt door L Bouton)
L-Bouton-Clasp.JPG
Ter inspiratie :-)